Sources Of Drinking Water in Beaumont, Texas
Where does Beaumont get its water from? The City of Beaumont has two sources of water: (1) well water, which is pumped from the Chicot Aquifer at three different well sites located in Hardin County, and (2) surface water from the Neches River. Well water is chlorinated before it is pumped to the city. Surface water receives a more complex treatment, including filtration and chlorination. The City of Beaumont inspects and analyzes both sources of water daily to ensure compliance with all federal and state requirements. The water plant is operated 24 hours a day, 7 days a week to give you the best-quality water possible. Contaminants may be found in drinking water that may cause taste, color, or odor problems. Sometimes the city has water line breaks. When they occur, the color comes from iron and mineral deposits inside the pipe that become dislodged.
Water treatment facilities consist of a surface water treatment plant and a well system including pumping and transfer facilities to provide safe drinking water of adequate quantities and sufficient pressure while meeting all state and federal regulations. The Surface Water Treatment Plant after the recent renovations is rated at 40 million gallons per day. The ground water system is a 17 million gallons per day facility consisting of three deep wells, four booster pumps and two 5 MG ground storage tanks. The City has six elevated water storage tanks with 6.8 million gallons of storage capacity, four ground water storage tanks with 17.7 million gallons of storage capacity, for a total of 24.5 million gallons of storage capacity. The Water Treatment Facilities are fully operable using SCADA controls that will automatically shut down the water discharge to the customers in case of water quality discrepancies. Is Beaumont's water safe to drink? Does Beaumont, TX put fluoride in the water?
Source: City of Beaumont, TX
Contaminants Found in Beaumont's Water Supply
(Detected above health guidelines)
3rd party independent testing found that this utility exceeds health guidelines for this drinking water contaminant. Aluminium (or Aluminum) is an extremely abundant heavy metal in the earth’s crust and is often found in the form of silicates such as feldspar. Aluminum has historically been considered to be relatively non-toxic in healthy individuals, who can tolerate oral daily doses of as much as 7.2 grams of aluminum without any apparent harmful effects. However, there is now abundant evidence that aluminum may cause adverse effects on the nervous system. Kidney disease patients who are exposed to high levels of aluminum in dialysis fluids and medications, develop dialysis encephalopathy, a progressive form of dementia characterized by speech and behavioral changes, tremors, convulsions, and psychosis. What are the risks of drinking tap water with Aluminium? It has been demonstrated that humans with these disorders tend to have high levels of aluminum in some areas of their brains, although it has not been demonstrated that the presence of aluminum in the brain initiates the onset of the diseases. Find out more about this contaminant and how to remove it here.
3rd party independent testing found that this utility exceeds health guidelines for this drinking water contaminant. Bromodichloromethane is one of the total trihalomethanes (TTHMs) that formed when disinfectants, such as chlorine, are used to treat tap water. What are the risks of drinking tap water with Bromodichloromethane? Cancer, Kidney & Liver Damage. Bromodichloromethane and other disinfection byproducts increase the risk of cancer and may cause problems during pregnancy. In recent animal studies, the main effect of eating or drinking large amounts of Bromodichloromethane is injury to the liver and kidneys. Find out more about this contaminant and how to remove it here.
3rd party independent testing found that this utility exceeds health guidelines for this drinking water contaminant. Chloroform, is a total trihalomethanes (TTHMs) which is formed when disinfectants are used to treat tap water. Most of the chloroform found in the environment comes from industry. Chloroform enters the environment from chemical companies and paper mills, It is also found in waste water from sewage treatment plants and drinking water to which chlorine has been added. Chlorine is added to most drinking water and many waste waters to destroy bacteria. Small amounts of chloroform are formed as an unwanted product during the process of adding chlorine to water. What are the risks of drinking tap water with chloroform? Cancer, central nervous system (brain), liver, and kidneys. Cancer of the liver and kidneys developed in rats and mice that ate food or drank water that had large amounts of chloroform in it for a long time. We do not know whether liver and kidney cancer would develop in people after long-term exposure to chloroform in drinking water. Based on animal studies, the Department of Health and Human Services has determined that chloroform may reasonably be anticipated to be a carcinogen (a substance that causes cancer). Find out more about this contaminant and how to remove it here.
3rd party independent testing found that this water utility exceeds health guidelines for this drinking water contaminant. The movie Erin Brockovich alerted the public to the great suffering the little town of Hinkley, California experienced due to hexavalent chromium in their drinking water. Today, Hinkley is little more than a ghost town thanks to continued water contamination, health concerns, and plummeting property values. Chromium (hexavalent) is a carcinogen that commonly contaminates American drinking water. Chromium (hexavalent) in drinking water may be due to industrial pollution or natural occurrences in mineral deposits and groundwater. What are the risks of drinking tap water with Chromium (hexavalent)? Cancer. A 2008 study by the National Toxicology Program, part of the National Institutes of Health, found that chromium-6 in drinking water caused cancer in laboratory rats and mice. That study and other research led scientists at the California Office of Environmental Health Hazard Assessment to conclude that chromium-6 can cause cancer in people. Find out more about this contaminant and how to remove it here.
3rd party independent testing found that this utility exceeds health guidelines for this drinking water contaminant. Dichloroacetic Acid is one of the five haloacetic acids and a member of the chloroacetic acids family. It is an essential chemical compound in medical research, especially in cancer treatment. This type of chloroacetic acid is a trace product of the process of chlorination of drinking water. Dichloroacetic Acid can get into water systems through improper disposal of waste from pharmaceutical factories. What are the risks of drinking tap water with Dichloroacetic acid? Cancer, Reproductive Issues, Child Development. Dichloroacetic Acid in drinking water may cause health problems during pregnancy, liver and kidney damage, reproductive difficulties, eyes and nerve problems, and an increased risk of getting cancer. Dichloroacetic Acid is common in municipal water since it is a trace product of the chlorination of drinking water. Find out more about this contaminant and how to remove it here.
3rd party independent testing found that this water utility exceeds health guidelines for this drinking water contaminant. Manganese is a naturally-occurring element that can be found ubiquitously in the air, soil, and water. Adverse health effects can be caused by inadequate intake or over exposure. Clogged water lines typically cause concentrations of manganese to increase. Clogs prevent chlorine from entering the distribution system. Chlorine is an oxidant, and is typically used to treat manganese in drinking water. What are the risks of drinking tap water with Manganese? Harm to the brain and nervous system. Reports have concluded that chronic ingestion of water containing manganese may lead to neurological effects in older adults and infants. Long term exposure can cause lethargy, muscular weakness. EPA set a “do not drink” advisory for infants under 1 year old and nursing and pregnant women. Find out more about this contaminant and how to remove it here.
3rd party independent testing found that this water utility exceeds health guidelines for this drinking water contaminant. Radiological contamination of water is due to the presence of radionuclides, which are defined as atoms with unstable nuclei. In an effort to become more stable, a radionuclide emits energy in the form of rays or high-speed particles. This is called ionizing radiation because it displaces electrons, which creates ions. The three major types of ionizing radiation are alpha particles, beta particles and gamma rays. Radiological contaminants leach into water from certain minerals and from mining. What are the risks of drinking tap water with Radiological contaminants? Cancer. Over and over again, regardless of the source, long-term exposure or brief exposure in high doses, leads to cancer. Cancers of the bone, liver, stomach, lungs, skin, kidneys, thyroid gland, and most other tissues are common, and medical science is still discovering other maladies that may be cancer-related. Find out more about this contaminant and how to remove it here.
Total Trihalomethanes (TTHMs)
3rd party independent testing found that this utility exceeds health guidelines for this drinking water contaminant. Total Trihalomethanes (TTHMs) are the result of a reaction between the chlorine used for disinfecting tap water and natural organic matter in the water. At elevated levels, TTHMs have been associated with negative health effects such as cancer and adverse reproductive outcomes. Now a study by government and academic researchers adds to previous evidence that dermal absorption and inhalation of TTHMs associated with everyday tap water use can result in significantly higher blood TTHM concentrations than simply drinking the water does. What are the risks of drinking tap water with Total Trihalomethanes (TTHMs)? Cancer. Studies from around the world including the United States & Europe have found that drinking tap water that carries Total Trihalomethanes increases the risk of developing cancer. In animal studies, all trihalomethanes cause liver, kidney and intestinal tumors. Find out more about this contaminant and how to remove it here.
3rd party independent testing found that this utility exceeds health guidelines for this drinking water contaminant. Trichloroacetic acid will get into your drinking water when naturally-occurring organic and inorganic compounds found in the water reacts with chlorine or other disinfectants used to purify drinking water. Trichloroacetic acid is one of the group of five haloacetic acids regulated by federal standards. What are the risks of drinking tap water with Trichloroacetic acid? Cancer & Pregnancy Issues. According to the Environmental Protection Agency (EPA), individuals exposed to the compound in excess of the "Maximum Contaminant Levels" during the duration of several years are prone to an increased risk of getting cancer. Long-term exposure to the chemical will increase your chances of acquiring a tumor. Oral exposure or the drinking of contaminated water may cause problems during pregnancy. It can also cause developmental issues to the fetus. Find out more about this contaminant and how to remove it here.
There is a drinking water standard of 4 ppm for fluoride but there is no health guideline for this contaminant and much is unknown about the effects of fluoride long term on the human body. This water utility did not exceed the drinking water standard for fluoride but fluoride was found in their water. Fluoride occurs naturally in surface and groundwater and is also added to drinking water by many water systems. The fluoride that is added to water is not the naturally occurring kind, the main chemicals used to fluoridate drinking water are known as “silicofluorides” (i.e., hydrofluorosilicic acid and sodium fluorosilicate). Silicofluorides are not pharmaceutical-grade fluoride products; they are unprocessed industrial by-products of the phosphate fertilizer industry (Gross!). Since these silicofluorides undergo no purification procedures, they can contain elevated levels of arsenic — more so than any other water treatment chemical. In addition, recent research suggests that the addition of silicofluorides to water is a risk factor for elevated lead exposure, particularly among residents who live in homes with old pipes. What are the risks of drinking tap water with Fluoride? Unknown. A growing body of evidence reasonably indicates that fluoridated water, in addition to other sources of daily fluoride exposure, can cause or contribute to a range of serious effects, including neurological issues, arthritis, damage to the developing brain, reduced thyroid function, and possibly osteosarcoma (bone cancer) in adolescent males. Animal studies indicate a moderate level of evidence that support adverse effects on learning and memory in animals exposed to fluoride in the diet or drinking water. Find out more about this contaminant and how to remove it here.
What are the best types of filters to remove these contaminants?
Water sources can contain contaminants that impact your long term health, the taste & smell of the water and other microbiological contaminants that can actually make people sick shortly after drinking. Fortunately, there are water filtration products that remove many of the impurities from water. These filters often use activated carbon. Activated carbon is a form of carbon processed to have small, low-volume pores that increase the surface area available for adsorption of contaminants or chemical reactions. Two dominant carbon filter choices are solid activated carbon blocks and granular activated carbon filters.
Granular activated carbon filters have loose granules of carbon that look like black grains of sand. These black grains of carbon, are dumped into a container and the water is forced to travel through the container to reach the other side, passing by all of the grains of carbon. Solid block carbon filters are blocks of compressed activated carbon that are formed with the combination of heat and pressure. These filters force the water to try to find a way through the solid wall and thousands of layers of carbon until the reach a channel which leads the water out of the filter. Both filters are made from carbon that’s ground into small particulate sizes. Solid carbon blocks are ground even further into a fine mesh 7 to 19 times smaller than the granular activated carbon filters.
Flow Channels & Less Contact Time
As water continually pass through Granular Activated Carbon filters, flow channels begin to develop that allows the water to flow around the carbon. Flow channels also develop between the granules, leading to less effective filtration as there’s less contact between the water and carbon. Solid carbon blocks are much tighter and won’t even let through microbial cysts like giardia and cryptosporidium (7 to 10 Microns in size). However, solid carbon block filters are so tight that they can often get plugged up with organic & non-organic matter, forcing owners to replace them on a more regular basis. This is why when you are using a Brita water pitcher filter (granular activated carbon), the filter will keep going and going long after it has stopped removing any water contaminants.
Carbon Block vs Granulated Activated Carbon
The granular activated carbon filters are cheap and simple to manufacture, which is why most water filtration companies choose this method for manufacturing (ex: Brita, Woder). Solid Carbon Block Filters on the other hand take longer to manufacture and are more expensive but with this expense, you get superior contaminant removal because the water must take a tortured path through thousands of layers of compressed carbon before it reaches your drinking glass.
The solid carbon block filters like the one used in the Epic Smart Shield & Epic Water Filter pitchers, remove more contaminants than the granular activated carbon filters due to the larger surface area and the tighter filters, this is why Epic Water Filters has standardized on the solid carbon block design for our water pitchers and our under the sink water filter. Unfortunately, granular activated carbon filters do not do enough to reduce contaminants, this is why they are not used when there is a chance of bacteria or cysts in the water. They are truly not "Epic" so that is why we have passed on this design and let our competitors like Woder, Brita, Pur, and Invigorated Water use these loose packed carbon filters for sub-par contaminant removal.
Solid carbon block filters, on the other hand, have millions and millions of different sized pores that cause the water to take a long slow path to get through the filter, increasing the contact time that the contaminated water has with the carbon. During this contact time is when contaminants adhere to the carbon and are removed from water. This happens during a process called adsorption, the other filtration method that carbon blocks use is called depth filtration where the thickness of the filter comes into play to help remove contaminants as they have to pass through this carbon walls.
With solid carbon block filters the contaminants are in contact with more carbon for a longer period and therefore have more time to remove stubborn contaminants like lead (Epic Pure Pitcher 99.9% removal), fluoride (Epic Pure Pitcher 97.8% removal), and PFCs (Epic Pure Pitcher 99.8% removal). Carbon blocks can remove chlorine more effectively, eliminate undesirable odors, and removal of endocrine disruptors like volatile organic compounds. Granular activated carbon filters, on the other hand, have small particles that move around under the pressure of water so they do not have as much uniformity throughout and therefore less contact time with the water and less contaminant removal.
What about Reverse Osmosis?
RO filters are good at contaminant removal. The downside of RO is that it wastes a lot of water. Each RO system wastes an average of 5 to 6 gallons for every gallon it produces of drinking water. Also RO systems remove trace minerals and other beneficial substances found in water that your body needs (calcium, manganese, iron and other important nutrients). This is why RO water is considered by many in the natural health world to be dead water and it is said that demineralized water is detrimental to general health due to vitamin and mineral depletion. The last downside of RO systems is that after your water passes through the filter process, it sits inside of steel drum that is lined with a butyl rubber bladder which is made from polyisobutylene. The filtered water sits in this butyl rubber bladder until it is used. All rubber and plastic containers leach into water at some level. Carbon block filters do not have this issue.
A Colorado based hiker, blogger, and water quality expert.
Impacted Zip Codes: 77701 77702 77703 77705 77706 77707 77708 77713 77704 77710 77720 77725 77726
*3rd party review of tap water provided by this water utility was in compliance with federal health-based drinking water standards. Health guidelines, mentioned on this page, were established by independent scientists who reviewed the scientific evidence, federal and state legal limits for drinking water contaminants, health advisories and risk assessments, and incorporated them all into the health guidelines referenced here. Information on source water was obtained from city water quality reports and may be subject to change based on your location and zip code. Please consult the latest water quality report for your neighborhood or home address for more accurate information. It’s important to note that only a handful of contaminants are required to be included in annual Consumer Confidence Reports or Water Quality Reports, and that there are hundreds of potentially harmful unregulated contaminants that aren’t accounted for by the EPA. Results of tests cited here were provided to an independent 3rd party by the state, as well as test information received from the U.S. EPA Enforcement and Compliance History database (ECHO). Water is very local so it is always recommended that you test your own tap water with a 3rd party laboratory. We have found 3rd party testing available from reputable labs between $150 to $400 but we do not give recommendations for labs. Currently we have not found a home water test kit that we would recommend and it is our opinion that TDS meters are not a reliable way to test water quality.